MSO2024信号示波器

Characteristics

Vertical System – Analog Channels

*¹ Bandwidth is 20 MHz at 2 mV/div, all models

Vertical System – Digital Channels

Horizontal System – Analog Channels

Horizontal System – Digital Channels

Acquisition Modes

Sample - Acquires sampled values

Peak Detect - Captures glitches as narrow as 3.5 ns at all sweep speeds

Averaging - From 2 to 512 waveforms included in average

Roll - Scrolls waveforms right to left across screen at sweep speeds slower than or equal to 40 ms/div

Trigger System

Main Trigger Modes - Auto, Normal, and Single

Trigger Coupling - DC, HF reject (attenuates >85 kHz), LF reject (attenuates <65 kHz), noise reject (reduces sensitivity)

Trigger Holdoff Range - 20 ns to 8 s

Trigger Signal Frequency Counter - Provides a higher accuracy means of identifying the frequency of trigger signals. Trigger Signal Frequency counter resolution is 6 digits.

Sensitivity

Internal DC Coupled

Trigger Level Range

Any Channel - ±4.92 divisions from center of screen

External (auxiliary input) - ±6.25V, 1x attenuation; ±12.5V, 10x attenuation

Trigger Modes

Edge - Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, HF reject, LF reject, and noise reject.

Pulse Width - Trigger on width of positive or negative pulses that are >, <, =, or ≠ to a specified period of time.

Runt - Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.

Logic - Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, NAND) specified for all analog and digital input channels defined as High, Low, or Don’t Care.

Setup and Hold - Trigger on violations of both setup time and hold time between clock and data present on any of the input channels.

Rise/Fall Time - Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either.

Video - Trigger on line number, all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals.

I²C (Optional) - Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I²C buses up to 3.4 Mb/s.

SPI (Optional) - Trigger on SS, Idle Time, MOSI, MISO, or MOSI and MISO on SPI buses up to 10.0 Mb/s.

CAN (Optional) - Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of Frame, Missing ACK, or Bit Stuffing Errors on CAN signals up to 1 Mb/s. Data can be further specified to trigger on ≤, <, =, >, ≥ or ≠ a specific data value. User-adjustable sample point is set to 50% by default.

RS-232/422/485/UART (Optional) - Trigger on Tx start bit, Rx start bit, Tx end of packet, Rx end of packet, Tx data, Rx data, Tx Parity Error, and Rx Parity Error.

LIN (Optional) - Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, or Errors such as Sync Parity or Checksum Errors.

Parallel (available on MSO models only) - Trigger on a parallel bus data value.

Waveform Measurements

Cursors - Waveform and Screen

Automatic Measurements - 29, of which up to four can be displayed on screen at any one time. Measurements include Frequency, Period, Delay, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area, and Cycle Area

Gating - Isolate the specific occurrence within an acquisition to take measurements, using either the screen or waveform cursors

Waveform Math

Arithmetic - Add, subtract, and multiply waveforms

Software

NI LabVIEW SignalExpress™ Tektronix Edition LE - A fully interactive measurement software environment optimized for the MSO2000/DPO2000 Series, enables you to instantly acquire, generate, analyze, compare, import, and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming. Standard MSO2000/DPO2000 Series support for acquiring, controlling, viewing, and exporting your live signal data is permanently available through the software. The full version (SIGEXPTE) adds additional signal processing, advanced analysis, mixed signal, sweeping, limit testing, and user-defined step capabilities and is available for a 30-day trial period standard with each instrument

OpenChoice® Desktop - Enables fast and easy communication between a Windows PC and the MSO2000/DPO2000 Series, using USB or LAN. Transfer and save settings, waveforms, measurements, and screen images

IVI Driver - Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI, Microsoft .NET and MATLAB

Display Characteristics

Display Type - 7 in (180 mm) liquid crystal TFT color display

Display Resolution - 480 horizontal x 234 vertical pixels (WQVGA)

Waveform Styles - Vectors, Dots (In Video Trigger mode), Variable Persistence, Infinite Persistence

Graticules - Full, Grid, Cross Hair, Frame

Format - YT and XY

Waveform Capture Rate - Up to 5,000 wfms/sec

Input/Output Ports

USB 2.0 High-Speed Host Port - Supports USB data storage devices and keyboards

USB 2.0 High-Speed Device Port - Rear-panel port supports communication/control of oscilloscope by PC and all PictBridge® compatible printers

LAN Port - RJ-45 connector, supports 10/100Base-T (requires DPO2CONN)

GPIB - Adapt USB 2.0 device port to a GPIB port (requires TEK-USB-488)

Video Out Port - DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector (requires DPO2CONN)

Auxiliary Input - Front-panel BNC connector. Input Impedance 1 MΩ ±2%. Max input 300 V_RMS with peaks ±450 V

Probe Compensator Output - Front-panel pins, Amplitude 5.0 V, Frequency 1 kHz

Kensington Lock - Rear-panel security slot connects to standard Kensington style lock

PowerSource

Power Source Voltage - 100 to 240 V ±10%

PowerSource Frequency -  45 to 65 Hz (90 to 264 V)360 to 440 Hz (100 to 132 V)

Power Consumption - 80 W maximum

TekVPI External Power Supply (119-7465-xx) - Output voltage: 12 V; Output current: 4.2 A; Power consumption: 50 W

Physical Characteristics

Rackmount Configuration – 4 U

Cooling Clearance - 50 mm (2 inches) on the left side and rear (when looking at the front of the instrument)

General Characteristics

Environmental

Temperature

Operating - 0 °C to +50 °C

Nonoperating - -40 °C to +71 °C

Humidity

Operating -  High: 30 °C to 50 °C, 5% to 60% Relative HumidityLow: 0 °C to 30 °C, 5% to 95% Relative Humidity

Nonoperating -  High: 30 °C to 55 °C, 5% to 60% Relative HumidityLow: 0 °C to 30 °C, 5% to 95% Relative Humidity

Altitude

Operating - 3,000 meters (9,843 feet)

Nonoperating - 12,000 meters (39,370 feet)

Random Vibration

Operating - 0.31 G_RMS from 5 to 500 Hz, 10 minutes each axis, 3 axes, 30 minutes total

Nonoperating - 2.46 G_RMS from 5 to 500 Hz, 10 minutes each axis, 3 axes, 30 minutes total

Regulatory

Electromagnetic Compatibility - 2004/108/EC

Safety -  Listed UL61010–1: 2004, CAN/CSA-C22.2 No. 61010.1: 2004;Complies with EN61010–1: 2001,Complies with the Low Voltage Directive 2004/108/EC for Product Safety

Ordering Information

MSO2000 Models

MSO2012 - 100 MHz, 1 GS/s, 1 M record length, 2+16 channel mixed signal oscilloscope

MSO2014 - 100 MHz, 1 GS/s, 1 M record length, 4+16 channel mixed signal oscilloscope

MSO2024 - 200 MHz, 1 GS/s, 1 M record length, 4+16 channel mixed signal oscilloscope

DPO2000 Models

DPO2012 - 100 MHz, 1 GS/s, 1 M record length, 2-channel digital phosphor oscilloscope

DPO2014 - 100 MHz, 1 GS/s, 1 M record length, 4-channel digital phosphor oscilloscope

DPO2024 - 200 MHz, 1 GS/s, 1 M record length, 4-channel digital phosphor oscilloscope

All models include: One P2221 200 MHz, 1x/10x Passive Probe per Analog Channel, User Manual and Translated Front-Panel Overlay, Documentation CD (063-4118-xx), OpenChoice® Desktop Software, NI LabVIEW SignalExpress™ Tektronix Edition LE Software, Calibration certificates document measurement traceability to National Metrology Institute(s) and ISO9001 Quality System Registration, Power Cord, and a three-year warranty. MSO models also include one P6316 16-channel logic probe and accessory kit, and accessory bag (016-2008-xx)

Please specify power plug and manual version when ordering

Recommended Serial Bus Application Modules

DPO2EMBD - Embedded Serial Triggering and Analysis Module. Enables triggering on packet level information on I²C and SPI buses as well as analytical tools such as bus views, packet decoding, search tools, and packet decode tables with timestamp information

DPO2COMP - Computer Serial Triggering and Analysis Module. Enables triggering on packet level information on RS-232/422/485/UART buses as well as analytical tools such as bus views, packet decoding, search tools, and packet decode tables with timestamp information

DPO2AUTO - Automotive Serial Triggering and Analysis Module. Enables triggering on packet level information on CAN and LIN buses as well as analytical tools such as bus views, packet decoding, search tools, and packet decode tables with timestamp information

Options

International Power Plugs

Opt. A0 - North America power.

Opt. A1 - Universal EURO power.

Opt. A2 - United Kingdom power.

Opt. A3 - Australia power.

Opt. A5 - Switzerland power.

Opt. A6 - Japan power.

Opt. A10 - China power.

Opt. A11 - India power.

Opt. A99 - No power cord or AC adapter.

Language Options*¹

Opt. L0 - English manual.

Opt. L1 - French manual.

Opt. L2 - Italian manual.

Opt. L3 - German manual.

Opt. L4 - Spanish manual.

Opt. L5 - Japanese manual.

Opt. L6 - Portuguese manual.

Opt. L7 - Simplified Chinese manual.

Opt. L8 - Standard Chinese manual.

Opt. L9 - Korean manual.

Opt. L10 - Russian manual.

Opt. L99 - No manual.

Service Options*²

Opt. C3 - Calibration Service 3 years.

Opt. C5 - Calibration Service 5 years.

Opt. CA1 - Provides a single calibration event, or coverage for the designated calibration interval, whichever comes first.

Opt. D1 - Calibration Data Report.

Opt. D3 - Calibration Data Report 3 years (with Opt. C3).

Opt. D5 - Calibration Data Report 5 Years (with Opt. C5).

Opt. R5 - Repair Service 5 years (including warranty).

Recommended Probes

TAP1500*³ - 1.5 GHz TekVPI single-ended active probe.

TDP0500*^3, *⁵ - 500 MHz TekVPI 42 V differential probe.

TCP0030*³ - 120 MHz TekVPI 30 Ampere AC/DC current probe.

TCP0150*³ - 20 MHz TekVPI 150 Ampere AC/DC current probe.

TCPA300/400*⁶ - Current measurement system amplifiers.

TCP305 - DC to 50 MHz, 50 A current probe for use with TCPA300.

TCP404XL - DC to 2 MHz, 500 A current probe for use with TCPA400.

P5100 - 2.5 kV, 100X high-voltage passive probe.

P5200 - 1.3 kV, 50X/500X, 25 MHz high-voltage active differential probe.

P5205*^3, *⁴ - 1.3 kV, 100 MHz high-voltage differential probe.

P5210*^3, *⁴ - 5.6 kV, 50 MHz high-voltage differential probe.

ADA400A*^3, *⁴ - 100x, 10x, 1x, 0.1x high-gain differential amplifier.

Recommended Accessories

DPO2CONN - Adds Ethernet (10/100Base-T) and Video Out Port.

Service manual - Order 071-2331-xx (English only).

TPA-BNC*³ - TekVPI to TekProbe BNC Adapter.

TekVPI External Power Supply - Order 119-7465-xx.

TEK-USB-488 - GPIB to USB Adapter.

Digital Probe Leadset (8 Channels) - Order 196-3508-xx.

TEK-DPG*³ - TekVPI Deskew Pulse Generator Signal Source.

Deskew and Calibration Fixture - Order 067-1686-xx.

Rackmount Kit - Order RMD2000. Does not include slide-out rails.

Soft Transit Case and Front Protective Cover - Order ACD2000.

Front Protective Cover - Order 200-5045-xx.

Hard Transit Case - Order HCTEK4321 (Requires ACD2000).

SIGEXPTE - NI LabVIEW SignalExpress™ Tektronix Edition Software (Full Version).

USB Keyboard - Order 119-7083-00.

Soft carrying case with front protective cover for MSO2000 and DPO2000 Series (ACD2000)

 

Warranty

Three-year warranty covering all parts and labor, excluding probes.

*¹ Language options include translated front-panel overlay for the selected language(s)

*² Probes and accessories are not covered by the oscilloscope warranty and Service Offerings. Refer to the datasheet of each probe and accessory model for its unique warranty and calibration terms

*³ Requires TekVPI external power adapter (119-7465-00); one per oscilloscope

*⁴ Requires TPA-BNC adapter

*⁵ Probes terminate into 50 Ω but oscilloscope will automatically adjust to account for 1 MΩ input

*⁶ Requires 50 Ω feed through termination between the oscilloscope input and the BNC cable